Tektronix TDS3000 Instrukcja Użytkownika Strona 83
- Strona / 140
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Maintenance
TDS3000 Series Service Manual
6–7
You will need the following tools to remove and replace all the modules in the
oscilloscope.
Torque-limiting screwdriver, 12 in ⋅ lb (1.3 N ⋅ m) range with Torx T-10
and T-15 tips (If you are using a magnetic screwdriver with interchangeable
bits, the T-15 bit must be a long bit, at least 5 cm (2 in) overall length).
Screwdriver with
1
8
inch flat blade
3
16
inch nut driver
Needle-nose pliers
You will need a
1
8
inch flat-bladed screwdriver to remove the handle.
Removal. Use this procedure to remove the handle.
1. Use the
1
8
inch flat-bladed screwdriver to pry the hub cover off of each side
of the handle.
2. Raise the handle to its full upright position.
3. Locate the handle hub on the display side of the oscilloscope.
NOTE. Do not remove the screw at the center of the handle hub.
4. Use the needle-nose pliers to pull the metal pin in the display-side hub
outward approximately 5 mm (0.2 in). If you accidentally pull the metal pin
all the way out, reinsert it half way. See Figure 6–1.
Tools Required
Handle
- Service Manual 1
- TDS3000 Series 1
- 071-0382-01 1
- WARRANTY 3
- List of Figures 7
- List of Tables 9
- Table of Contents 10
- TDS3000 Series Service Manual 10
- General Safety Summary 11
- Symbols and Terms 12
- Preventing Electrostatic 13
- Battery Recycling 13
- Service Safety Summary 15
- Related Manuals 17
- Service Programs 18
- Contacting Tektronix 18
- Specifications 19
- Operating Information 31
- Transporting the Oscilloscope 32
- Connecting Power 33
- Operating Safely with 34
- Battery Power 34
- Installing and Removing 35
- Charging the Battery 36
- Application modules 37
- Contacts 37
- Latching tab 39
- Using the Menu System 40
- VERTICAL 41
- Using the Menu Buttons 42
- Using the Dedicated 43
- Controls 43
- Identifying Items in the 45
- Using Quick Menus 46
- Front-Panel Connectors 48
- Rear-Panel Connectors 49
- Probe Compensation 50
- Self Calibration 51
- Theory of Operation 53
- Battery Board 54
- Main Board 54
- Display Module 55
- Front-Panel Board 55
- Disk Drive 55
- Performance Verification 57
- Test Record 58
- Self Test 60
- Check DC Voltage 61
- Measurement Accuracy 61
- Check Bandwidth 63
- Oscilloscope model Frequency 64
- TDS3012, TDS3014 100 MHz 64
- TDS3032, TDS3034 300 MHz 64
- TDS3052, TDS3054 500 MHz 64
- Check Channel 65
- Edge-Trigger Sensitivity 65
- Check Sample Rate and 67
- Delay Time Accuracy 67
- Adjustment Procedures 69
- Signal Connections 71
- Apply Pk-Pk Voltage to a 72
- Apply Fast Rise Step 73
- Signal to all Channels 73
- Apply DC Voltage to 73
- External Trigger 73
- Factory Adjustment Procedure 74
- Inspection and Cleaning 78
- Preparation 81
- List of Modules 81
- Summary of Procedures 82
- Tools Required 83
- Metal pin 84
- Rotate the handle 85
- Pull on the handle 85
- Rear Case 87
- Communication 88
- Pins are face 89
- Disk drive 89
- Rear Chassis 91
- Front Chassis and Display 99
- Chassis assembly 100
- Side up and push out 100
- Display chassis 100
- Front chassis 101
- Cable post 101
- Front-panel cable 101
- Display Inverter Board 102
- Push tab 104
- Display module 104
- Clears tab 104
- Backlight tubes (2) 105
- Display glass 106
- Foam faces up 106
- Front Panel 107
- Front panel keypad 109
- Bezel keypad 109
- Make sure lock 110
- Troubleshooting 111
- Troubleshooting Procedure 112
- Maintenance 113
- Unpacking 119
- Repacking 119
- Electrical Parts List 123
- Diagrams 125
- Mechanical Parts List 127
- Module Servicing 128
- Abbreviations 128
- Mfr. Code to Manufacturer 129
- Cross Index 129
- Exploded Views 129
- Replaceable parts list 131
- Accessories list 139
- Accessories list (cont.) 140
Casio YA-D30 Operaciones básicas manuali
Manuali dei proprietari e guide per l'utente per Proiettori Casio YA-D30 Operaciones básicas.
We fornisce 1 manuali pdf Casio YA-D30 Operaciones básicas per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Komentarze do niniejszej Instrukcji